Error Codes Starting with F – Overview by Brand
1. Whirlpool / Common Brands (e.g. ApplianceAlliance)
| Error Code | Meaning | Troubleshooting |
| F01 | Electronic circuit board fault | Unplug for ~2 minutes, then try restart; if persists, call technician Appliance Alliance |
| F02 | Motor circuit fault (no or intermittent drum rotation) | Call technician Appliance Alliance |
| F03 | Temperature sensing fault | Call technician Appliance Alliance |
| F05 | Waste pipe blockage or pump issue | Check pump filter, hoses; call technician if unresolved Appliance Alliance |
| F06 | Door lock fault | Inspect for obstructions; call technician if still failing Appliance Alliance |
| F07 | Circuit board/heating circuit fault | Call technician Appliance Alliance |
| F08 | Heater fault | Call technician Appliance Alliance |
| F09 | Software fault (display malfunction) | Call technician Appliance Alliance |
| F11 | Pump circuit fault (not draining) | Call technician Appliance Alliance |
| F12 | Electronic control fault (won’t power on) | Call technician Appliance Alliance |
| F13 | Dryer temperature sensing fault (washer-dryers) | Call technician Appliance Alliance |
| F15 | Heater control fault (wash/dry) | Call technician Appliance Alliance |
| F16 | Drum lock position sensor fault (top-load only) | Call technician Appliance Alliance |
| F18 | Internal data error (display/functions don’t work) | Unplug ~2 mins, restart; call if persists Appliance Alliance |
| F19 | Fan motor/heating fault (washer-dryers) | Call technician Appliance Alliance |
<button aria-label="Copy Table"></button>
2. Indesit / Yorkshire Appliances
| Error Code | Meaning | Troubleshooting |
| F01 | Short circuit (motor issue) | Reset; if persists, inspect motor Yorkshire Appliances |
| F02 | Motor jam | Reset; inspect motor for obstruction Yorkshire Appliances |
| F03 | Circuitry issue (thermistor) | Reset; check temperature sensor Yorkshire Appliances |
| F04 | Pressure switch problem | Reset; inspect pressure switch Yorkshire Appliances |
| F05 | Pressure switch/pump filter blockage | Reset; clean pump filter Yorkshire Appliances |
| F07 | Heater relay problem | Reset; test heater relay Yorkshire Appliances |
| F08 | Severe heater relay fault | Reset; inspect relay Yorkshire Appliances |
| F09 | Electronic/wiring setup issue | Reset; inspect wiring/components Yorkshire Appliances |
| F10 | Pressure switch sensor error | Reset; check sensor Yorkshire Appliances |
| F11 | Pump failure | Reset; check pump Yorkshire Appliances |
| F12 | Connectivity fault | Reset; inspect wiring Yorkshire Appliances |
| F13 | Over-temperature fault | Reset; test temperature sensor Yorkshire Appliances |
| F14 | Hybrid too low heat (washer-dryer) | Reset; check heating element Yorkshire Appliances |
| F15 | Heater relay error | Reset; inspect relay Yorkshire Appliances |
| F17 | Door lock failure | Reset; clean lock, replace if needed Yorkshire Appliances |
| F18 | Control board fault | Reset; inspect board Yorkshire Appliances |
<button aria-label="Copy Table"></button>
3. Bosch WFP Series (Kenya context)
| Error Code | Meaning |
| F01 | Water intake timeout / inlet hose blocked / low pressure |
| F02 | Heating element timeout / water not heating |
| F03 | Slow or failed drainage / level-pressure or pump fault |
| F04 | Motor startup failure |
| F05 | Motor start or worn brushes issue |
| F06 | NTC sensor short-circuit |
| F07 | NTC circuit fault |
| F08 | Door open at program start |
| F09 | Unexpected heating |
| F10 | Communication error |
| F11 | Motor control PCB or heatsink overheated |
| F12 | Motor short-circuit or fault |
| F13 | High supply voltage |
| F14 | Low supply voltage |
| F15 | General fault — call qualified engineer Best Appliance Repairs |
<button aria-label="Copy Table"></button>
4. Miele
| Error Code | Meaning |
| F1 / F2 | NTC thermistor short-circuit |
| F10 | Water intake fault |
| F11 | Drainage issue |
| F15 | Hot water intake fault |
| F16 | Excess detergent detected |
| F19 | Rotation issue due to slow flow |
| F20 | Water fill/flood protection issue |
| F29 | Steam heating inactive |
| F34 / F35 | Door lock issues |
| F39 | Main electronic unit failure |
| F41 | Incorrect data from faulty electricals |
| F43 | Model not programmed (for service) |
| F45 | Flash RAM (memory) defective |
| F50 / F51 | Drive or level sensor issues Appliance Service Centre Repairs |
<button aria-label="Copy Table"></button>
General Reset & Troubleshooting Tips
- Soft reset: Often unplugging the machine for 2–5 minutes, pressing Pause/Cancel twice, then the Power button once can clear many F-codes The Sprucekhojdeal.comReddit.
- Limitations: Some codes indicate component failure—like board faults, relay or pump issues—and require professional repairs or part replacements.
- Model-specific variation: Error meanings may differ by brand/model. Always consult your machine’s manufacturer manual or support site for accuracy.
KEY
- “F-codes” range widely in meaning—from sensor or motor faults to electronic and electrical issues.
- Commonly, reset by power cycling may clear the code, but persistent errors typically require diagnostics or part replacement.
- Tables above group codes by brand to help you track and address them.
